Description
1.How to connect wires
The wire connection of this wireless backup camera and monitor kit is very simple. There is no need to run extra RCA cable through the vehicle, because the transmission of video signal is wireless. All you need to do is powering the camera and the monitor.
1.Before mounting the camera, please connect the wireless transmitter to your reverse light power.
2.Insert the monitor's cigarette lighter plug into car cigarette lighter interface to power the monitor. Then check if the camera and monitor kit works properly.
3.If it works normally, then you can install the backup camera. If it can not work normally, please check whether the wire is correctly connected. If it still doesn't work after checking, please contact us for more support
2.How to power the camera
Connect the power to the camera and you can do that by simply connecting it to the red wire and the 12 volts power. Black cable should go to the ground as usual. The Power that goes to the camera often comes from the reverse tail light. Fuse the transmitter wires with the reverse light wires. Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire. For safety, make sure you wrap the combined wires in electrical tape.
System Features:
Instantly Sends Camera Video to LCD Display
Simple Installation
Monitor Display:
LCD size/type: 4.3' TFT LCD Screen
Power Supply: 12V
Rear View Camera :
IP-68 Waterproof
Resolution:628x582
Rotatable Angle: 170 Degree
Frame rate: 30fps
Power Supply:12V
Package Including
1 x 4.3 LCD Monitor With One Cigarette Lighter
1 x Rear View Camera
1 x Installation Manual
The wire connection of this wireless backup camera and monitor kit is very simple. There is no need to run extra RCA cable through the vehicle, because the transmission of video signal is wireless. All you need to do is powering the camera and the monitor.
1.Before mounting the camera, please connect the wireless transmitter to your reverse light power.
2.Insert the monitor's cigarette lighter plug into car cigarette lighter interface to power the monitor. Then check if the camera and monitor kit works properly.
3.If it works normally, then you can install the backup camera. If it can not work normally, please check whether the wire is correctly connected. If it still doesn't work after checking, please contact us for more support
2.How to power the camera
Connect the power to the camera and you can do that by simply connecting it to the red wire and the 12 volts power. Black cable should go to the ground as usual. The Power that goes to the camera often comes from the reverse tail light. Fuse the transmitter wires with the reverse light wires. Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire. For safety, make sure you wrap the combined wires in electrical tape.
System Features:
Instantly Sends Camera Video to LCD Display
Simple Installation
Monitor Display:
LCD size/type: 4.3' TFT LCD Screen
Power Supply: 12V
Rear View Camera :
IP-68 Waterproof
Resolution:628x582
Rotatable Angle: 170 Degree
Frame rate: 30fps
Power Supply:12V
Package Including
1 x 4.3 LCD Monitor With One Cigarette Lighter
1 x Rear View Camera
1 x Installation Manual
B-Qtech Backup Camera and Monitor Kit-4.3" Front/Rear View Reverse Camera Waterproof Adjustable Easy Installation for Cars,Trucks,Pickups,Bus,Van
Price is below average
Current Price
$35.99
Average
$38.99
Min Price
$33.99
Max Price
$44.99
Price dynamics
8%
Description
1.How to connect wires
The wire connection of this wireless backup camera and monitor kit is very simple. There is no need to run extra RCA cable through the vehicle, because the transmission of video signal is wireless. All you need to do is powering the camera and the monitor.
1.Before mounting the camera, please connect the wireless transmitter to your reverse light power.
2.Insert the monitor's cigarette lighter plug into car cigarette lighter interface to power the monitor. Then check if the camera and monitor kit works properly.
3.If it works normally, then you can install the backup camera. If it can not work normally, please check whether the wire is correctly connected. If it still doesn't work after checking, please contact us for more support
2.How to power the camera
Connect the power to the camera and you can do that by simply connecting it to the red wire and the 12 volts power. Black cable should go to the ground as usual. The Power that goes to the camera often comes from the reverse tail light. Fuse the transmitter wires with the reverse light wires. Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire. For safety, make sure you wrap the combined wires in electrical tape.
System Features:
Instantly Sends Camera Video to LCD Display
Simple Installation
Monitor Display:
LCD size/type: 4.3' TFT LCD Screen
Power Supply: 12V
Rear View Camera :
IP-68 Waterproof
Resolution:628x582
Rotatable Angle: 170 Degree
Frame rate: 30fps
Power Supply:12V
Package Including
1 x 4.3 LCD Monitor With One Cigarette Lighter
1 x Rear View Camera
1 x Installation Manual
The wire connection of this wireless backup camera and monitor kit is very simple. There is no need to run extra RCA cable through the vehicle, because the transmission of video signal is wireless. All you need to do is powering the camera and the monitor.
1.Before mounting the camera, please connect the wireless transmitter to your reverse light power.
2.Insert the monitor's cigarette lighter plug into car cigarette lighter interface to power the monitor. Then check if the camera and monitor kit works properly.
3.If it works normally, then you can install the backup camera. If it can not work normally, please check whether the wire is correctly connected. If it still doesn't work after checking, please contact us for more support
2.How to power the camera
Connect the power to the camera and you can do that by simply connecting it to the red wire and the 12 volts power. Black cable should go to the ground as usual. The Power that goes to the camera often comes from the reverse tail light. Fuse the transmitter wires with the reverse light wires. Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire. For safety, make sure you wrap the combined wires in electrical tape.
System Features:
Instantly Sends Camera Video to LCD Display
Simple Installation
Monitor Display:
LCD size/type: 4.3' TFT LCD Screen
Power Supply: 12V
Rear View Camera :
IP-68 Waterproof
Resolution:628x582
Rotatable Angle: 170 Degree
Frame rate: 30fps
Power Supply:12V
Package Including
1 x 4.3 LCD Monitor With One Cigarette Lighter
1 x Rear View Camera
1 x Installation Manual
Price will be lower
in next 2 weeks
in next 2 weeks
According to the data, price will be lower in next two weeks, so not waste your money and track better price!
Product review & video
[Music] hello viewers this doubt too fast here in today's video I will show you how to install a very simple backup camera system in your vehicle for this install I'll be using this alyc Wave vehicle backup camera and an esky 4.3 inch TFT LCD monitor both items are very inexpensive you can pick up this camera for $30 and this LCD display for $22 let me first unbox the backup camera so you can see what it looks like this is the video cable you run from the front of the vehicle to the back this is the back up camera self this is power cable this is user manual here's the LCD monitor this is power cable user guide this modder has a 4.3 inch color LCD display with a resolution of 480 by 272 and an aspect ratio of 16 to 9 it operates on 12 volt DC at the bottom you have this base you can rotate 180 degrees double sided tape at the bottom so you stick this onto your dash at the back this is t


